The piping solution provider: www.pdxsteel.com

Stub End

Size: 1/2"-48"
Wall thickness: SCH5S-SCHXXS
Material: Special Alloy, Super Duplex Stainless Steel, Stainless Steel, Carbon Steel, Titanium
Standards: ASME B16.9, MSS SP 43

  • PRODUCT DETAIL
  • Material

Size: 1/2″ to 48″ / DN15 to DN600
Wall thickness: SCH5S-SCHXXS
Type: Type A, Type B, Type C
Material: Special Alloy, Super Duplex Stainless Steel, Stainless Steel, Carbon Steel, Titanium
Standards: ASME B16.9, MSS SP 43
Length: Long Pattern and Short Pattern

Lap Joint Stub End

Stub end is directly contact with pipes and medium whereas the flanges doesn’t. Therefore, the material grades of stub ends should satisfy the design and service conditions, while flanges can be made of lower grades to save the total cost.

STUB END TYPES

Stub ends are available in three different types, named “Type A”, “Type B” and “Type C”:

  • The first type (A) is manufactured and machined to match standard lap joint backing flange (the two products have to be used in combination). The mating surfaces have an identical profile to permit a smooth loading of the flare face
  • Stub ends type B are have to be used with standard slip-on flanges
  • Type C stub ends can be used either with lap joint or slip-on flanges and are manufactured from pipes

Stub end types

SHORT/LONG PATTERN STUB ENDS (ASA/MSS)

Stub ends are available in two different patterns:

  • the short pattern, called MSS-A stub ends
  • the long pattern, called ASA-A stub ends (or ANSI length stub end)

Short and long pattern stub ends

Short pattern (MSS) and long pattern stub ends (ASA)

STUB END FINISH

Stub ends can be ordered with different ends finishing:

  • Beveled Ends
  • Squared Ends
  • Flanged Ends
  • Grooved Ends
  • Threaded Ends (Male Only)

Lap Joint Stub End Metric Dimensions as per ASME B16.9

Lap Joint Stub End

NPS ODMax ODMin LPF SPF R G
1/2 22.8 20.5 76 51 3 35
3/4 28.1 25.9 76 51 3 43
1 35.0 32.6 102 51 3 51
1-1/4 43.6 41.4 102 51 5 64
11/2 49.9 47.5 102 51 6 73
2 62.4 59.5 152 64 8 92
2-1/2 75.3 72.2 152 64 8 105
3 91.3 88.1 152 64 10 127
3-1/2 104.0 100.8 152 76 10 140
4 116.7 113.5 152 76 11 157
5 144.3 140.5 203 76 11 186
6 171.3 167.5 203 89 13 216
8 222.1 218.3 203 102 13 270
10 277.2 272.3 254 127 13 324
12 328.0 323.1 254 152 13 381
NPS ODMax ODMin LPF SPF R G
14 359.9 354.8 305 152 13 413
16 411.0 405.6 305 152 13 470
18 462.0 456.0 305 152 13 533
20 514.0 507.0 305 152 13 584
22 565.0 558.0 305 152 13 641
24 616.0 609.0 305 152 13 692

GENERAL NOTES:

(a) All dimensions are in millimeters.
(b) See Table 13 for tolerances.
(c) Service conditions and joint construction often dictate stub end length requirements. Therefore, the purchaser must specify long or
short pattern fitting when ordering.

NOTES:

(1) Gasket face finish shall be in accordance with ASME B16.5 for raised face flanges.
(2) The lap thickness T shall not be less than nominal pipe wall thickness. See Table 13 for maximum tolerance.
(3) When short pattern stub ends are used with larger flanges in Classes 300 and 600, with most sizes in Classes 900 and higher, and
when long pattern stub ends are used with larger flanges in Classes 1500 and 2500, it may be necessary to increase the length of the
stub ends in order to avoid covering the weld with the flange. Such increases in length shall be a matter of agreement between the
manufacturer and purchaser.
(4) When special facings such as tongue and groove, male and female, etc., are employed, additional lap thickness must be provided and
such additional thickness shall be in addition to (not included in) the basic length F.
(5) These dimensions conform to the radius established for lap joint flanges in ASME B16.5.
(6) This dimension conforms to standard machined facings shown in ASME B16.5. The back face of the lap shall be machined to conform
to the surface on which it seats. Where ring joint facings are to be applied, use dimension K as given in ASME B16.5.

Pipe Fittings Dimensions Tolerance as per ASME B16.9

Dimension Tolerance

Dimensions butt welded Stub Ends schedule 10SMSS SP-43 type A/B

Stubend
NPS OD T G F R
Type A
R
Type B
1/2 21.3 2.11 34.9 50.8 3.05 0.76
3/4 26.7 2.11 42.9 50.8 3.05 0.76
1 33.4 2.77 50.8 50.8 3.05 0.76
1.1/4 42.2 2.77 63.5 50.8 4.83 0.76
1.1/2 48.3 2.77 73 50.8 6.35 0.76
2 60.3 2.77 92.1 63.5 7.87 0.76
2.1/2 73 3.05 104.8 63.5 7.87 0.76
3 88.9 3.05 127 63.5 9.65 0.76
3.1/2 101.6 3.05 139.7 76.2 9.65 0.76
Stubend
NPS OD T G F R
Type A
R
Type B
4 114.3 3.05 157.2 76.2 11.18 0.76
5 141.3 3.40 185.7 76.2 11.18 1.52
6 168.3 3.40 215.9 88.9 12.7 1.52
8 219.1 3.76 269.9 101.6 12.7 1.52
10 273.1 4.19 323.9 127 12.7 1.52
12 323.9 4.57 381 152.4 12.7 1.52
14 355.6 4.78 412.8 152.4 12.70 1.52
16 406.4 4.78 469.9 152.4 12.7 1.52
18 457.2 4.78 533.4 152.4 12.70 1.52
20 508 5.54 584.2 152.4 12.70 1.52
24 609.6 6.35 692.2 152.4 12.7 1.52

Dimensions are in millimeters unless otherwise indicated. Weights are in kilograms and approximately given.

DIMENSIONAL TOLERANCES OF STUB ENDS MSS SP-43

Nominal Pipe Size 1/2 up to 2.1/2 3 to 3.1/2 4 5 to 8 10 to 18 20 to 24
Outside Diameter at Welding End (OD) 0.8 0.8 0.8 + 1.6
– 0.8
+ 2.29
– 0.76
+ 3.05
– 0.76
Overall Length (F) 1.6 1.6 1.6 1.6 2 2
Outside Diameter of Lap (G) + 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
Thickness of Lap (T) + 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
Fillet Radius of Lap (R) + 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
Wall Thickness (t) Not less than 87.5% of Nominal Wall Thickness

Dimensional tolerances are in millimeters unless otherwise indicated.

Notes:

  • Type A for Lap Joint Flanges
  • Type B for Slip On Flanges
  • MSS SP-43 only covers stainless steel buttweld fittings made for use with Schedule 5S and 10S pipe and Stub Ends suitable for use with Schedule 40S pipe, as defined in ASME B36.19. The dimensions and dimensional tolerances defined in MSS SP-43 are substantially the same as those in ASME B16.9 specifications from NPS 1/2 – NPS 24. Except with regard to the outside diameter at the bevel.
Summary
product image
Aggregate Rating
5 based on 1 votes
Brand Name
Acero
Product Name
Stub end
Price
USD 1-10000
Product Availability
Pre-Order Only

Material

Special Alloys

  • HASTELLOY® X
  • MONEL® R-405
  • MONEL® K-500
  • HASTELLOY® C-276
  • HASTELLOY® C-22
  • HASTELLOY® B-2
  • INCOLOY® 825
  • INCOLOY® 800H / 800HT®
  • INCONEL® 718
  • INCONEL® ALLOY 625
  • INCONEL® ALLOY 601
  • INCONEL® ALLOY 600
  • MONEL® ALLOY 400

ALLOY 20

  • NICKEL 200/201
  • MONEL® R-405
  • MONEL® K-500
  • MONEL® ALLOY 400
  • INCONEL® 718
  • INCONEL® ALLOY 625
  • INCONEL® ALLOY 601
  • INCONEL® ALLOY 600
  • INCOLOY® 825
  • HASTELLOY® X
  • HASTELLOY® C-276
  • HASTELLOY® C-22
  • HASTELLOY® B-2
  • INCOLOY® 800H / 800HT®
  • HASTELLOY® B-3

Duplex Stainless Steel

  • ZERON® 100, SUPER DUPLEX STAINLESS STEEL
  • Super Duplex S32760
  • LDX 2101®, DUPLEX STEEL
  • Duplex S31803
  • SUPER DUPLEX 2507
  • DUPLEX 2205

Stainless Steel

  • STAINLESS STEEL NITRONIC 50HS
  • STAINLESS STEEL NITRONIC 60
  • STAINLESS STEEL NITRONIC 50
  • STAINLESS STEEL 13-8PH
  • STAINLESS STEEL 15-5PH
  • STAINLESS STEEL PRODEC 303
  • STAINLESS STEEL 303
  • STAINLESS STEEL 446
  • STAINLESS STEEL 410S
  • STAINLESS STEEL 410
  • STAINLESS STEEL 304-304H
  • STAINLESS STEEL 17-4
  • STAINLESS STEEL 347
  • STAINLESS STEEL 440C
  • STAINLESS STEEL 309
  • STAINLESS STEEL 316-316l
  • STAINLESS STEEL AL-6XN®
  • STAINLESS STEEL 330
  • STAINLESS STEEL 321
  • 317L STAINLESS STEEL
  • STAINLESS STEEL 310/310S
  • Stainless Steel 304L
  • Stainless Steel 304
  • STAINLESS STEEL 253 MA

Carbon Steel

  • CARBON STEEL PRODUCTS

Titanium

  • 10V-2Fe-3Al
  • 6Al-4V
  • 6Al-4V STA
  • 6Al-4V ELI
  • 6Al-2Sn-4Zr-2Mo

PREV
Inquery now

SUBSCRIBE TO OUR NEWSLETTER

FOLLOW US

YouTube
العربية简体中文繁體中文NederlandsEnglishFrançaisDeutschItaliano日本語한국어LatinPortuguêsРусскийEspañolTürkçe

QQ
Email me
Mail to us